Відео

klomp tos

Copper mesh

V.GOOD

Can you or did you use any solvents or cleaners to assist cleaning out the manifold?

Did this welder just have a two pin conection

So what makes this not a bomb if you close the valve?

Nice work, great ideas. Your device looks like it likely has a pinched bend , SEE @ 09:05. Heating/ Annealing the tube before before making this harder bend. OR cut and use a 90* elbow?( or a swage joint)

Can you make these in 15amp? I want to run 2x 15amp 3000w low density elements in my 65l still.

I use a 30 gallon barrel. I freeze 6 gallon jugs of water the night before distilling. I then use a little giant pump which is great. The entire run stays cold and the little giant is a great pump.

me gusta mucho tu destilador (condensador . tienes que hacer otro vidio como se enrolla el el tubo ,que no es facir felicitaciones .tan tanvien se ve deliciosa esa cerveza.

Great work..

the condenser should be slanted

Die suck nogal eh

Brass in a still is a big no no. Very bad. Do not copy this numpty.

You really, really shouldn't be "teaching" people. Brass has no place in distillation. Your 50L still build video shows a LOT of brass in it. Very, very bad news.

Why the out put water from reflux condenser is not going back to 120 litter tank? 120 litter is enough to run full distillation process?

I have a 2" T500 kit with condenser and 4 floor 3" bubble plate kit with 2" to 3" reducer get 96% proof without fail from start to finish and run it at condenser at 51c - 55c max. I take off 250mls heads and get 2.500mls in quality 96%. Bubble plate don't give me tails and the the purity and smell is amazing. I use pure turbo yeast for white spirit and turbo yeast classic 8 for dark spirits. Never use that charcoal or a+b clear just the turbo yeast ONLY. Takes 8 days to finish and with 7g dextrose sugar 1 teaspoon of nutrition and 30Lwater. That's it. Takes roughly 4-5hrs to finish the still. If you run it too fast eg. 77c you get more quantity at lower proof which more like a strip run but I always aim for 96% and water it down to 40% but either way don't matter because you goto water it down. Absolutely love that parrot going to make that one. And your still setup is a beauty 👍👍👍

How degassed does it have to be. I shake and it keeps spitting bubbles out

No brass in a still

Interested in the SCR controller.. Do you have a link for it? I think I'll need to go for 120Vac vs 240

My preferred method (yours may be more relevant): put the copper mesh and stainless scrubbers into a large mason jar and fill with vinegar. Inspect after a few days: if everything is clean and unrusted, you have reliable material. Rinse well. Insert the copper so that it's at the top of the column, then the stainless in a ratio about 3 x stainless to 1 copper. Finally, pick up the column and then try breathing thru it. If you can't, it's packed too tightly. I avoid ceramics because I have seen them harbour mould in the past in other applications.

Am a newbie to distilling, and my nature is always to find the simplest solution, and you have helped me find that Dan. And for that you have my grateful thanks. I am in a Motorhome in Turkiye. Copper fittings are very hard to find here, can just get 12mm copper pipe, so this is a brilliant condenser solution. Can I brew my mash and distill in a Campervan....Watch this space....Thanks again.

Best video that I found on this processing. Thanks for sharing. Gonna give this a try without the essence using chips only base and added honey. Did you end up racking it another time? Thanks

Did you use high pressure water to clean the throttle body?

More Meneer, I have lately started distilling (but have been making beer and wine for almost 30 years. (that sounds bad) I want to make mampoer like we got in South Africa. Have you any recipes you could give me. I have a pot still which I was given but have made a boka still (I saw Louwrens van der Merwe in NZ still)

are you using real money to buy the molasses or monopoly money rotfl 4 dollars for 2 rotflmfao can you post the receipt would love to see the receipt

56% silver solder without cadmium is the best for this app. Good mechanical fit would only use a tiny bit. Heat the brass, stainless is a poor conductor. Once the silver melts, it instantly makes the stainless touching the joint at liquidus temperature and prevents over heat which makes black oxide. Use the recommended flux on joint surface.

What kind of probe port fitting did you use for your digital thermometer?

🇮🇷🇮🇷🇮🇷

Hi this video is awesome DIY filter. When I pour in my 40 ABV and it drips through when it starts filling up and going and then the filter will be submerged in the alcohol will it carry on filling up my bottom container and drip all the contents of alcohol so there none left at the top??

Git muza

Thanks👍

Great work! I’m about to move over to distilling been making beer for about 12 years now! I gonna have to build one of those now:) Thanks for all the tips and if you have one too many sitting around I would be interested in taking one off your hand:) Cheers Mate

Wow, Just What I've Been L@@Kn 4. Do Share Cut List? I have All Bell/Reducers, Fittings and Pipe.

Where did you get your still if you made it what did you use

good job Buddy!

Landmark soundtrack of the mid 1970z.

Shouldn't your water inlet be at the bottom and your outlet at the top. That way you be cooling your condenser correctly

Nice copper work. Neat setup, in my country you can do anything you want but make liquor. 😔 95% your reflux is working nicely.

Legend thanks heaps

My question is why... i have a pot a thumper and condenser and mine comes out 150 160 and perfectly fine. Just saying. Nice set up though

single 3 inch yuck why don't you go twin 3 inch single 3 inch is two small

I’ve learnt more from watching your 5 minute videos than other people’s 20 minute ramblings Champion

Does it work?

Well if you didn't add carbon to it you could have saved the stuff in the bottom for dunder for your next run. And you don't need the part A part B clear stuff. You really think the guys making rum in the 16 17 or 1800s added stuff like that?

A little iffy about the brass, but all in all this is a really cool build man! Good work.

Don't pack your column tight or force it until it becomes blocked or partially block, the back pressure can make this a GIANT bomb...Loose is better really...

This shoud take one min,you used five.

Hey mate just wondering is that the 58L urn from ebay? If so is it any good? Thinking of getting one for a BIAB setup Cheers 🍻

Zinc and Brass are two big no no's